[1]张丹丹,周志强,沈 煜,等.基于热电偶原理的三相变压器绕组材料检测方法[J].高压电器,2019,55(09):254-260.[doi:10.13296/j.1001-1609.hva.2019.09.035]
 ZHANG Dandan,ZHOU Zhiqiang,SHEN Yu,et al.Testing Method for Winding Materials of Three-phase Transformers Based on Principle of Thermocouple[J].High Voltage Apparatus,2019,55(09):254-260.[doi:10.13296/j.1001-1609.hva.2019.09.035]
点击复制

基于热电偶原理的三相变压器绕组材料检测方法()
分享到:

《高压电器》[ISSN:1001-1609/CN:61-11271/TM]

卷:
第55卷
期数:
2019年09期
页码:
254-260
栏目:
技术讨论
出版日期:
2019-09-10

文章信息/Info

Title:
Testing Method for Winding Materials of Three-phase Transformers Based on Principle of Thermocouple
作者:
张丹丹1 周志强2 沈 煜2 杨 帆2
(1. 华中科技大学强电磁工程与新技术国家重点实验室, 武汉 430074; 2. 国网湖北省电 力公司电力科学研究院, 武汉 430077)
Author(s):
ZHANG Dandan1 ZHOU Zhiqiang2 SHEN Yu2 YANG Fan2
(1. State Key Laboratory of Advanced Electromagnetics Engineering and Technology , Huazhong University of Science and Technology, Wuhan 430074, China; 2. State Grid Hubei Electric Power Research Institute, Wuhan 430077, China)
关键词:
材料检测 绕组材料 三相变压器 热电偶原理
Keywords:
materials testing winding material oil-immersed three-phase transformer principle of thermocouple
DOI:
10.13296/j.1001-1609.hva.2019.09.035
摘要:
变压器的质量直接影响电网供电的安全性和可靠性,而绕组材料检测在变压器质量管 控过程中变得越来越重要。文中针对油浸式三相变压器提出了一种绕组材料检测方法。该方法 基于热电偶原理,通过检测仅存在于非铜绕组变压器中的寄生热电偶实现绕组材料判别。为使 变压器相间产生温差,提出了一种非对称电热方法,寄生热电偶则通过检测相应的热电势来识 别。为探究检测方法的可行性同时制定合适的加热时间,采用数值仿真计算了变压器的温度分 布以及热电势的理论值。通过铝绕组变压器和铜绕组变压器的试验验证了检测方法的有效性。 该方法简单、有效、无需特殊的检测仪器,同时适用于其他带绕组的设备。
Abstract:
A new method for testing winding material of an oil-immersed three- phase transformer was proposed based on the principle of thermocouple. In this method, the winding material is recognized by detecting the parasitic thermocouples which only exist in the transformer with non-copper windings. An asymmetric electric heating mode was presented to generate temperature difference among the phases of the windings, and then the parasitic thermocouples could be found out by detecting the corresponding thermal electromotive forces. In order to verify the feasibility of the proposed testing method and acquire appropriate heating time, the temperature distribution in transformer and the theoretical values of the thermal electromotive forces were numerically computed. Testing results of the transformers with respective aluminum and copper windings verified the effectiveness of the winding material testing method. This method requires no special devices, and it is simple and applicable to other power equipment with windings.

参考文献/References:

[1] General requirements for liquid-immersed distribution, power, and regulating transformers:IEEE Std C57.12.00—2000[S]. 2000.
[2] MILLS B, REDFORD A H. Machinability of engineering materials[M]. London ’New York: Applied Science Publishers, 1987.
[3] TRIPATHY S C, LAKERVI E. Evaluation of transformer loading above nameplate rating[J]. Electric MAchines and Power Systems, 2000, 28(7): 625-636.
[4] Power transformers: Part 5-Ability to withstand short-circuit:IEC 60076 -5:2006[S]. 2006.
[5] WATERS M. The short-circuit strength of power transformers[M]. London: Macdonald & Co., 1966.
[6] SULLIVAN C R. Aluminum windings and other strategies for high-frequency magnetics design in an era of high copper and energy cost[J]. IEEE Trans on Power Electron, 2008, 23(4): 2044-2051.
[7] POLOUJADOFF M, MIPO J C, NURDIN M. Some economical comparisons between aluminum and copper squirrel cages[J]. IEEE Trans. Energy Convers, 1995, 10(3): 415-418.
[8] 方福林,陈叔涛,阙家桢. 论我国铝线变压器的发展与展望[J]. 中国电机工程学报 ,1984,4(3):12-20. FANG Fulin,CHEN Shutao,QUE Jiazhen. Development of aluminium winding transformer in china and their propects[J]. Proceedings of the CSEE,1984 ,4(3):12-20.
[9] GEORGILAKIS P S, GIOULEKAS A T, SOUFLARIS A T. A decision tree method for the selection of winding materials in power transformers[J]. Journal of Materials Processing Technology, 2007(181): 281-285.
[10] 陈金猛,潘 斌,李志新,等.配电变压器绕组材质辨识研究现状及展望[J]. 变 压器,2016, 53(11):16-19. CHEN Jinmeng, PAN Bin, LI Zhixin, et al. Status and prospect of winding material identification research of distribution transformer[J]. Transformer, 2016, 53(11): 16-19.
[11] FINLEY W R, HODOWANEC M M. Selection of Copper versus Aluminum rotors for induction motors[J]. IEEE Transactions on Industry Applications, 2001, 37 (6): 1563-1573.
[12] POLLOCK D D. The theory and properties of thermocouple elements[M]. CT: Omega Press, 1979: 1-23.
[13] PURUSHOTHAMAN S, DE LEON F. Heat-transfer model for toroidal transformers[J]. IEEE Trans. Power Del.April., 2012, 27(2): 813-820.
[14] MAHAJAN S M, ROBALINO D M, SIVAN V. Thermal modeling of an inverted- type oil-immersed current transformer[J]. IEEE Transactions on Power Delivery, 2010, 25(4): 2511-2518.
[15] 王 羽,李晓萍,罗思敏,等. 垂直型直流接地极暂态温升计算与试验[J]. 中国 电机工程学报,2013, 33(10):184-190. WANG Yu, LI Xiaoping, LUO Simin, et al. Test and computation for vertical ground electrode’s transient temperature rise [J]. Proceedings of the CSEE, 2013, 33(10): 184-190.
[16] POTTER D. Measuring temperature with thermocouples-A tutorial[Z]. USA:Texas Instruments Co., Ltd., 1996.
[17] WHITMAN L C, HOLCOMB J E. Transient temperature rise of transformers [J]. Power Apparatus and Systems,Part III.Transactions of the American Institute of Electrical Engineers, 1962, 81(3): 1046-1053.
[18] IEEE guide for loading mineral-oil-immersed transformers:IEEE Std C57.91—1995(R2004)[S]. Transformers Committee of the IEEE Power Engineering Society,2004.
[19] 油浸式电力变压器负载导则:GB/T 15164—1994[S].1994. Loading guide for oil-immersed power transformers:GB/T 15164—1994[S].1994.

备注/Memo

备注/Memo:
收稿日期:2019-01-19; 修回日期:2019-03-12 基金项目:国网湖北省电力公司科技基金项目(521532160013)。 Project Supported by State Grid Hubei Electric Power Company Science and Technology Fund(521532160013).张丹丹(1968—),女,博士,副教授,研究方向为电气设备状态检测、过电压与绝缘 配合、高电压新技术。 周志强(1987—),男,博士,工程师,从事高电压技术研究。 沈 煜(1983—),男,硕士,高级工程师,从事高电压技术研究。 杨 帆(1982—),男,博士,高级工程师,从事高电压技术研究。
更新日期/Last Update: 2019-09-10