1.国网江苏省电力有限公司,南京 211703
2.国网江苏省电力有限公司电力科学研究院,南京 211103
3.重庆邮电大学 自动化学院,重庆 400065
宋博(1989-),男(汉),高级工程师,江苏南京,硕士,主要从事高电压与试验技术,邮箱:1430769166@qq.com。
高思航(1990-),男(汉),副教授,重庆,博士,主要从事电工装备故障诊断与在线监测,邮箱:gaosh@cqupt.edu.cn。
收稿:2025-09-19,
修回:2025-10-17,
录用:2025-11-26,
移动端阅览
宋博, 蔚超, 林元棣, 等. 加速热老化下丙烯酸酯密封圈力学性能与气密性的协同退化行为研究[J/OL]. 高压电器, 2026.
SONG Bo, WEI Chao, LIN Yuandi, et al. Study on the synergistic degradation behavior of mechanical properties and air tightness of acrylate seals under accelerated thermal aging[J/OL]. High VoltageApparatus, 2026.
本文针对广泛应用于油浸式变压器的丙烯酸酯密封圈,开展其在热-应力-油侵蚀多因素作用下的加速老化试验,定期测试密封圈关键力学参数,通过氮气保压气密性试验确定密封圈气密性失效终点,结合FTIR与SEM探究其老化机理,揭示老化过程中密封圈力学性能退化与气密性失效的关联规律,并以气密性失效作为寿命终点,建立丙烯酸酯密封圈寿命预测模型。结果表明:热老化过程中丙烯酸酯力学性能呈显著退化趋势,其中压缩永久变形率先升后平缓、拉断伸长率先降后平缓、硬度先降后升、拉伸强度先升后降。110℃、120℃和130℃下丙烯酸酯分别老化至第53天、38天、17天时出现气密性失效;FTIR结果表明断链、交联及氧化反应是密封圈力学性能退化与气密性失效的原因。SEM结果表明老化过程中密封圈的表面和断面孔隙率升高,颗粒物聚集、孔洞、局部裂痕等逐渐增多,老化过程中变形率持续上升并逐渐平缓的拐点与气密性失效点的密封圈微观形貌差异较大,表明老化过程中密封圈内部分子结构损伤是导致其气密性失效的关键因素。基于Arrhenius定律预测丙烯酸酯密封圈在热-应力-油侵蚀环境下使用温度为30-80℃时的服役寿命分别为9.24-0.42年。
This paper conducts accelerated aging tests on acrylate seals widely used in oil-immersed transformers under the combined action of multiple factors including heat
stress
and oil erosion. The key mechanical parameters of the seals are regularly tested
and the end point of airtightness failure of the seals is determined through the nitrogen pressure-holding airtightness test. The aging mechanism is explored by combining FTIR and SEM. The correlation law between the degradation of the mechanical properties of the seals and airtightness failure during the aging process is revealed. Taking airtightness failure as the end point of the service life
a life prediction model for acrylate seals is established. The results show that during the thermal aging process
the mechanical properties of acrylate seals exhibit a significant degradation trend. Specifically
the compression set first increases and then levels off
the elongation at break first decreases and then levels off
the hardness first decreases and then increases
and the tensile strength first increases and then decreases. Airtightness failure occurs on the 53rd
38th
and 17th days of aging at 110°C
120°C
and 130°C
respectively. FTIR results indicate that chain scission
cross-linking
and oxidation reactions are the causes of the degradation of the mechanical properties and airtightness failure of the seals. SEM results show that the porosity of surface and cross section of seal ring increases
particle aggregation
pores and local cracks increase gradually during aging. The micro-morphology of the seals at the inflection point where the deformation rate continuously increases and then gradually levels off during the aging process differs significantly from that at the airtightness failure point
indicating that the damage to the internal molecular structure of the seals during the aging process is the key factor leading to airtightness failure. Based on the Arrhenius law
the service life of acrylate seals in a heat-stress-oil erosion environment at operating temperatures of 30 - 80°C is predicted to be 9.24 - 0.42 years
respectively.
麻守孝 , 邓军 , 黎大健 , 等 . 基于Arrhenius的换流主变压器密封寿命预估 [J ] . 广西电力 , 2023 , 46 ( 04 ): 8 - 14 .
MA Shouxiao , DENG Jun , LI Dajian , et al . Seal life estimation of converter main transformer based on arrhenius [J ] . Guangxi Electric Power , 2023 , 46 ( 04 ): 8 - 14 .
连鸿松 . 电气设备橡胶密封件失效原因分析与对策 [J ] . 高压电器 , 2019 , 55 ( 12 ): 234 - 239 .
LIAN Hongsong . Analysis and Countermeasures of the Failure of Rubber Seals in Electrical Equipment [J ] . High Voltage Apparatus , 2019 , 55 ( 12 ): 234 - 239 .
王欣欣 , 何成 , 陈军 , 等 . GIS设备用三元乙丙橡胶密封材料老化前后力学性能变化研究 [J ] . 高压电器 , 2024 , 60 ( 08 ): 106 - 112 .
WANG Xinxin , HE Cheng , CHENG Jun , et al . Study on Mechanical Property Variation of EPDM Sealing Materials for GIS Equipment Before and After Aging [J ] . High Voltage Apparatus , 2024 , 60 ( 08 ): 106 - 112 .
WEN Xishan , YUAN Xiaoqing , LAN Lei , et al . Effect of transformer oil on room temperature vulcanized silicone rubber [J ] . IEEE Transactions on Dielectrics and Electrical Insulation , 2017 , 24 ( 4 ): 2337 - 2343 .
赵耀洪 , 钱艺华 , 陈天生 , 等 . SF6气密封橡胶材料气体渗透特性研究 [J ] . 高压电器 , 2019 , 55 ( 10 ): 116 - 120+127 .
ZHAO Yaohong , QIAN Yihua , CHEN Tiansheng , et al . Experimental Study on SF6 Gas Permeation Characteristics of Rubber Sealing Materials [J ] . High Voltage Apparatus , 2019 , 55 ( 10 ): 116 - 120+127 .
Ghosh P , Chakraborty R , Das C . K. Thermal degradation characteristics of acrylate rubber in transformer oil environment [J ] . Polymer Degradation and Stability , 2017 , 136 : 58 - 67 .
张保卫 . 碳纤维/炭黑/丁腈橡胶复合材料的物理性能和导电性能 [J ] . 橡胶工业 , 2017 , 64 ( 12 ): 709 - 713 .
ZHANG Baowei . Physical properties and conductive performance of carbon fiber/carbon black/nitrile rubber composites [J ] . Rubber Industry , 2017 , 64 ( 12 ): 709 - 713 .
LIU Y , WANG X . Research on property variation of silicone rubber and EPDM rubber under interfacial multi-stresses [J ] . IEEE Transactions on Dielectrics and Electrical Insulation , 2019 , 26 ( 6 ): 2027 - 2035 .
CHEN C , JA Z , YE W , et al . Thermo-oxidative aging analysis of HTV silicone rubber used for outdoor insulation [J ] . IEEE Transactions on Dielectrics and Electrical Insulation , 2017 , 2 4 ( 3 ): 1761 - 1772 .
LIU Q , SHI W , LI K , et al . Performance degradation prediction and reliability evaluation of rubber aging in natural environment under alternating cyclic thermal load [J ] . IEEE Access , 2019 , 7 : 63027 - 63035 .
李呆 , 卓文越 , 杨国 , 等 . 多因素耦合作用下丁腈橡胶的老化行为和机理研究 [J ] . 高分子学报 , 2021 , 52 ( 7 ): 762 - 774 .
LI Dai , ZHUO Wenyue , YANG Guo , et al . Aging behavior and mechanisms of nitrile rubber under multi-factor coupling effects [J ] . Chinese Journal of Polymer Science , 2021 , 52 ( 7 ): 762 - 774 .
ZHANG L , WANG J , LI X . Accelerated aging behavior of ACM rubber seals for power transformers under thermal stress [J ] . IEEE Transactions on Dielectrics and Electrical Insulation , 2020 , 27 ( 3 ): 1021 - 1028 .
WANG Y , CHEN H , LIU M . Stress relaxation behavior of rubber seals under combined thermal and mechanical loading [J ] . Polymer Testing , 2019 , 75 : 12 - 19 .
LI H. , ZHANG K , YANG W . Swelling and degradation of ACM rubber in mineral insulating oil [J ] . Materials Chemistry and Physics , 2021 , 258 : 123456 .
CHEN C , THOMAS S . Oxidation mechanism of acrylate rubber in oil-immersed environment [J ] . Polymer Degradation and Stability , 2018 , 149 : 52 - 61 .
LIU X , ZHAO Y , SUN Q . Ozone attack on rubber seals under partial discharge in transformers [J ] . High Voltage , 2022 , 7 ( 2 ): 321 - 330 .
廖姗姗 , 何东升 , 覃凯宁 , 等 . 基于Arrhenius模型的油浸式变压器橡胶密封圈寿命评估 [J ] . 绝缘材料 , 2022 , 55 ( 03 ): 59 - 66 .
LIAO Shanshan , HE Dongsheng , QIN Kaining , et al . Life evaluation of rubber sealing ring of oil-immersed transformer based on arrhenius model [J ] . Insulating Materials , 2022 , 55 ( 03 ): 59 - 66 .
韩哲文 , 季昌国 , 林林 , 等 . 丁腈橡胶热空气和热油老化力学性能研究及服役寿命预测 [J ] . 绝缘材料 , 2024 , 57 ( 12 ): 66 - 73 .
HAN Zhewen , JI Changguo , LIN lin , et al . Mechanical properties research and service life prediction of nitrile rubber in thermal air ageing and oil ageing [J ] . Insulation Materials , 2024 , 57 ( 12 ): 66 - 73 .
王振龙 , 季昌国 , 韩哲文 , 等 . 不同加速老化条件对500 kV变压器用丁腈橡胶老化行为的影响 [J ] . 绝缘材料 , 2025 , DOI: 10.16790/j.cnki.1009-9239.im.2025.06.013 http://dx.doi.org/10.16790/j.cnki.1009-9239.im.2025.06.013 .
WANG Zhenlong , JI Changguo , HAN Zhewen , et al . Effect of different accelerated ageing conditions on ageing behavior of nitrile rubber for 500 kV transformer [J ] . Insulation Materials , 2025 , DOI: 10.16790/j.cnki.1009-9239.im.2025.06.013 http://dx.doi.org/10.16790/j.cnki.1009-9239.im.2025.06.013 .
罗恒煜 , 李斐婕 , 李俊宇 , 等 . 氟橡胶和丁腈橡胶的耐热氧老化性能与寿命预测研究 [J ] . 橡胶工业 , 1 - 5
LUO Hengyu , LI Feijie , LI Junyu , et al . Research on the Heat and Oxygen Aging Resistance and Life Prediction of Fluoroelastomers and Nitrile Butadiene Rubber [J ] . China Rubber Industry , 1 - 5 .
GB/T531.1-2008 . 硫化橡胶或热塑性橡胶压入硬度试验方法第1部分:邵氏硬度计法 [S ] . 2008 .
GB/T531.1-2008 . Rubber, vulcanized or thermoplastic-Determination of indentation hardness-Part 1: Duromerer method [S ] . 2008 .
GB/T7759.1-2015 . 硫化橡胶或热塑性橡胶压缩永久变形的测定第1部分:在常温及高温条件下 [S ] . 2015 .
GB/T7759.1-2015 . Rubber, vulcanized or thermoplastic-Determination of compression set-Part 1: At ambient or elevated temperatures [S ] . 2015 .
GB/T528—2009 . 硫化橡胶或热塑性橡胶拉伸应力应变性能的测定 [S ] . 2009 .
GB/T528—2009 . Rubber, vulcanized or thermoplastic-Determination of tensile stress-strain properties [S ] . 2009 .
0
浏览量
0
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
陕公网安备 61010402000197