国网山西省电力公司电力科学研究院,太原 030001
西安交通大学电气学院,西安 710049
李艳鹏(1982—),男,硕士,正高级工程师,主要研究方向为高压试验和带电检测技术(E-mail:liyanpeng1982@163.com)
李军浩(1980—),男,博士,长期从事高电压现场试验和状态感知技术的研究和教学(通信作者)(E-mail:junhaoli@xjtu.edu.cn)。
收稿:2026-05-10,
修回:2026-07-23,
纸质出版:2026-11-16
移动端阅览
李艳鹏, 李永祥, 张昱, 等. 大温差条件下直流穿墙套管温度场分布特性研究[J]. 高压电器, 2026,62(11):177-185.
LI Yanpeng, LI Yongxiang, ZHANG Yu, et al. Research on Temperature Field Distribution Characteristics of DC Wall Bushing Under Large Temperature Difference Conditions[J]. High Voltage Apparatus, 2026, 62(11): 177-185.
李艳鹏, 李永祥, 张昱, 等. 大温差条件下直流穿墙套管温度场分布特性研究[J]. 高压电器, 2026,62(11):177-185. DOI: 10.13296/j.1001-1609.hva.2026.11.022.
LI Yanpeng, LI Yongxiang, ZHANG Yu, et al. Research on Temperature Field Distribution Characteristics of DC Wall Bushing Under Large Temperature Difference Conditions[J]. High Voltage Apparatus, 2026, 62(11): 177-185. DOI: 10.13296/j.1001-1609.hva.2026.11.022.
直流穿墙套管是特高压换流站连接阀厅和直流场的重要设备,其运行环境特殊,户外侧温度受运行环境影响。对于山西北部,冬季室外温度接近-30 ℃,单日昼夜温差可达30 ℃,研究大温差条件下穿墙套管的绝缘失效机理对于提升套管运行可靠性、制定合理运维策略具有重要意义。文中依据直流穿墙套管实际结构,采用半稳态的计算方法构建了套管热—流耦合仿真模型,对于单一环境温度以及环境温度随时间动态变化时套管内部温度变化情况进行仿真计算,并对比稳态法与半稳态法在计算大温差条件时套管内部各点温度分布差异。仿真结果表明,单一环境温度下,环境温度越低套管内部温差越大,流速分布变化较小。环境温度随时间变化时,套管内部不同位置的温度随时间变化趋势有所不同。半稳态仿真较稳态仿真更接近于真实的温度变化过程,最恶劣的工况出现在环境温度极值处。
DC wall bushing is an important equipment for connecting the valve hall and DC field in ultra-high voltage converter stations. Its operating environment is special and the outdoor side temperature is affected by the operating environment. For the northern part of Shanxi province in China
the outdoor temperature in winter is close to -30 ℃ and the diurnal temperature difference can reach 30 ℃. Studying the insulation failure mechanism of wall bushing under large temperature differences is of a great significance for improving bushing operation reliability and formulating resonable operation and maintenance strategies.Based on the actual structure of DC wall bushing in this paper
a semi- steady state calculation method is adopted to construct a thermal fluid coupling simulation model of the bushing. The simulation calculation is carried out for the temperature variation inside the bushing under a single environmental temperature and dynamic changes over time. The temperature distribution differences at various points inside the bushing are compared between the steady state method and the semi - steady state method when calculating large temperature differences. The simulation results show that in case of single ambient temperature
the lower the ambient temperature
the greater the temperature difference inside the bushing
and the smaller the variation in flow velocity distribution. When the ambient temperature changes over time
the trend of temperature variation at different positions inside the bushing varies. The semi- steady state simulation is closer to the real temperature variation process than steady state simulation
and the worst operating conditions occur at the extreme environmental temperature.
孙龙勇,姚灿江,刘英英,等. 新型515 kV直流SF 6 气体绝缘穿墙套管研发设计[J ] .高压电器,2023,59(5):28-34.
Sun Longyong, Yao Canjiang, Liu Yingying, et al. Development and design of new 515 kV DC SF 6 gas insulated wall bushing[J ] . High Voltage Apparatus, 2023, 59(5):28-34.
黎斌,王日新,于欣,等. 超/特高压直流套管的研发新思路——±800 kV电容式复合绝缘穿墙套管结构设计的探讨[J]. 高压电器,2021,57(7):1-11.
Li Bin, Wang Rixin, Yu Xin, et al.New idea on the development of EHV/UHVDC bushing -discussion on structure design of ±800 kV capacitive composite insulated wall bushing[J]. High Voltage Apparatus, 2021, 57(7):1-11.
韩晓东,陈晓东,李杨,等. 电热耦合场分析在±800 kV穿墙套管电场分布计算应用[J]. 高压电器,2023,59(5):35-42.
Han Xiaodong, Chen Xiaodong, Li Yang, et al. Application of electrothermal coupling field analysis to electric field distribution calculation of ±800 kV wall bushing[J]. High Voltage Apparatus, 2023, 59(5):35-42.
王青于,靳守锋,袁书文,等. 特高压环氧浸纸—SF 6 气体复合绝缘穿墙套管界面电荷积累过程和直流电场分布特性仿真[J ] . 高电压技术,2022,48(10):4102-4112.
Wang Qingyu, Jin Shoufeng, Yuan Shuwen, et al. Simulation of interface charge accumulation progress and DC electric field distribution characteristics of the UHV epoxy impregnated paper - SF 6 [J ] . High Voltage Engineering, 2022, 48(10):4102-4112.
程显,刘赛,葛国伟,等. ±400 kV直流穿墙套管用环保气体的绝缘特性[J]. 电工技术学报,2025,40(3):900-912.
Cheng Xian, Liu Sai, Ge Guowei, et al. Insulation characterization of environmentally friendly gases for ± 400 kV DC wall bushing[J]. Transactions of China Electrotechnical Society, 2025, 40(3): 900-912.
谢雄杰,罗晓庆,胡伟,等. 不均匀淋雨条件下SF 6 绝缘直流穿墙套管直流电压闪络特性[J ] . 高电压技术,2021,47(6):2084-2090.
Xie Xiongjie, Luo Xiaoqing, Hu Wei, et al. DC voltage flashover characteri stics of SF 6 insulated DC wall bushing under uneven rain conditions[J ] . High Voltage Engineering, 2021, 47(6):2084-2090.
刘杉,宋胜利,卢理成,等. ±800 kV特高压直流穿墙套管故障分析及设计改进[J]. 高电压技术,2019,45(9):2928-2935.
Liu Sha, Song Shengli, Lu Licheng, et al. Failure analysis and design improvement of ± 800 kV UHVDC wall bushings[J]. High Voltage Engineering, 2019, 45(9):2928-2935.
王彤. 特高压直流穿墙套管外绝缘研究及结构优化设计[D]. 武汉:武汉大学,2017.
Wang Tong. Research of external insulation and optimal design of structure for UHV DC wall bushing[D]. Wuhan: Wuhan University, 2017.
孙昭英,宿志一. 解决高压直流穿墙套管非均匀淋雨闪络的措施和途径[J]. 中国电力,1994(4):36-39.
Sun Zhaoying, Su Zhiyi. The measures and ways to solve the non - uniform rain flashover of HVDC wall bushing[J]. Electric Power, 1994(4):36-39.
孙昭英,来小康,陈行,等. 高压直流穿墙套管非均匀淋雨闪络及其防护措施[J]. 电网技术,1993(3):22-27.
Sun Zhaoying, Lai Xiaokang, Chen Hang, et al. Investigation of HVDC wall bushing flashover in nonuniform rain and preventive maintenance[J]. Power System Technology, 1993(3):22-27.
邱文严,陈军锋,周文正. 复杂天气下直流穿墙套管电场分布仿真研究[J]. 绝缘材料,2023,56(9):49-53.
Qiu Wenyan, Chen Junfeng, Zhou Wenzheng. Simulation on electric field distribution of DC wall bushing under complex weather conditions[J]. Insulating Materials, 2023, 56(9):49-53.
楚智霖,王青于,刘则希,等. 高压套管三维热—流耦合场数值计算方法与验证[J]. 电工技术学报,2026,41(15):5237-5248.
Chu Zhilin, Wang Qingyu, Liu Zexi, et al. Numerical calculation method and verification of three - dimensional thermal - fluid coupling field for high -voltage bushings[J]. Transactions of China Electrotechnical Society, 2026, 41(15):5237-5248.
王仲奕,童军心,赵彦珍. 高压交直流电容式套管内部电场的分析比较及改进[J]. 高压电器,2003,39(3):9-11.
Wang Zhongyi, Tong Junxin, Zhao Yanzhen. Comparison, analysis and improvement of the electric field distribution in high voltage AC and DC capacitive bushings[J]. High Voltage Apparatus, 2003, 39(3):9-11.
张启浩,吴德贯,马正霖. ±800 kV特高压直流输电工程直流穿墙套管设计缺陷及其改进方法[J]. 高压电器,2019,55(4):239-244.
Zhang Qihao, Wu Deguan, Ma Zhenglin. Defect and improved method of DC wall bushing design in ±800 kV UHVDC transmission project[J]. High Voltage Apparatus, 2019, 55(4):239-244.
张晋寅,韦晓星,夏谷林,等. 南方电网直流穿墙套管运行特性分析[J]. 电瓷避雷器,2019(4):230-236.
Zhang Jinyin, Wei Xiaoxing, Xia Gulin, et al. Operating characteristic analysis of DC wall bushings in CSG[J]. Insulators and Surge Arresters, 2019(4):230-236.
张施令,彭宗仁,刘鹏,等. 电热耦合模型应用于干式油气套管径向温度分布计算及其试验研究[J]. 电网技术,2012,36(12): 289-296.
Zhang Shiling, Peng Zongren, Liu Peng, et al. Experimental study on electro-thermal coupling model applied in computation of radial temperature distribution of RIP oil - gas bushing condenser[J]. Power System Technology, 2012, 36(12):289-296.
王青于,杨熙,彭宗仁,等. 应用三维电磁—热—流耦合场分析法计算换流变压器干式套管的温度场分布[J]. 中国电机工程学报,2016,36(22):6269-6275.
Wang Qingyu, Yang Xi, Peng Zongren, et al. 3D coupled electromagnetic - thermal - fluid method for computation of temperature field of converter transformer RIP bushings[J]. Proceedings of the CSEE, 2016, 36(22):6269-6275.
汤浩,李金忠,张贺军,等. 特高压直流换流变压器阀侧套管高环温强电流下轴径向的温度分布规律[J]. 中国电机工程学报,2017,37(18):5494-5503.
Tang Hao, Li Jinzhong, Zhang Hejun, et al. Axial and radial temperature distribution of the valve side bushing in UHVDC converter transformer under high ambient temperature and large current[J]. Proceedings of the CSEE, 2017, 37(18):5494-5503.
Yang Xiao, Yang Zhuodong, Zhang Yi, et al. Simulation analysis of electrical - thermal - fluid coupling property for supporting insulation in SF 6 filled HVDC apparatus[J ] . IEEE Transactions on Dielectrics and Electrical Insulation, 2022, 29(1):69-76.
Jyothi N S, Ramu T S. Statistical methods for accelerated life testing with particular reference to resin impregnated paper bushings[C]//2012 Asia - Pacific Power and Energy Engineering Conference, 2012:1-4.
Zhang Shibao. Evaluation of thermal transient and overload capability of high - voltage bushings with ATP[J]. IEEE Transactions on Power Delivery, 2009, 24(3):1295-1301.
温苗,林莘,仲思蒙. 变压器套管传热性能的数值模拟和试验验证[J]. 高电压技术,2016,42(9):2956-2961.
Wen Miao, Lin Xin, Zhong Simeng. Numerical simulation and experimental study of heat transfer characteristics in transformer bushing[J]. High Voltage Engineering, 2016, 42(9):2956-2961.
邓江. 干式SF 6 气体绝缘特高压直流套管的电热场分布特性及内绝缘结构优化设计研究[D ] . 成都:西南交通大学,2020.
Deng Jiang. Study on electric temperature field distribution characteristics and optimal design of internal insulation structure in dry - type SF 6 gas insulated UHVDC bushing[D ] . Chengdu: Southwest Jiaotong University, 2020.
许佐明,胡伟,张施令,等. 550 kV环氧浸渍干式油—SF 6 电容套管温度场分析[J ] . 高电压技术,2012,38(11):3087-3092.
Xu Zuoming, Hu Wei, Zhang Shiling, et al. Thermal field analysis for 550 kV epoxy resin - impregnated paper oil - SF 6 capacitor bushing[J ] . High Voltage Engineering, 2012, 38(11):3087-3092.
汪书苹,从伟,周勇,等. 变压器油老化对变压器套管温度场的影响[J]. 变压器,2022,59(3):18-22.
Wang Shuping, Cong Wei, Zhou Yong, et al. Effect of aging of transformer oil on temperature field of transformer bushing[J]. Transformer, 2022, 59(3):18-22.
0
浏览量
0
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
陕公网安备 61010402000197