Research on Interruption Process Simulation of Hybrid DC Circuit Breaker Based on Two-level Voltage Source Synthetic Test Method

YAN Duifeng; LIU Ping; FENG Lun; ZHANG Feifan; XIU Shixin; JIA Shenli; MO Yongpeng

doi:10.13296/j.1001-1609.hva.2024.05.010

您当前的位置：

首页 >

文章列表页 >

Research on Interruption Process Simulation of Hybrid DC Circuit Breaker Based on Two-level Voltage Source Synthetic Test Method

Research & Analysis | 更新时间：2025-04-26

- Research on Interruption Process Simulation of Hybrid DC Circuit Breaker Based on Two-level Voltage Source Synthetic Test Method
- High Voltage Apparatus Vol. 60, Issue 5, Pages: 76-83(2024)
- 作者机构：
  
  1.西安高压电器研究院股份有限公司，西安　 710077
  2.西安交通大学电气工程学院，西安　 710049
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2024.05.010
  CLC：
- Received：19 December 2023，
  
  Revised：09 February 2024，
  
  Published：16 May 2024
- 稿件说明：
移动端阅览
YAN Duifeng, LIU Ping, FENG Lun, et al. Research on Interruption Process Simulation of Hybrid DC Circuit Breaker Based on Two-level Voltage Source Synthetic Test Method[J]. High voltage apparatus, 2024, 60(5): 76-83.
DOI：

YAN Duifeng, LIU Ping, FENG Lun, et al. Research on Interruption Process Simulation of Hybrid DC Circuit Breaker Based on Two-level Voltage Source Synthetic Test Method[J]. High voltage apparatus, 2024, 60(5): 76-83. DOI： 10.13296/j.1001-1609.hva.2024.05.010.

摘要

直流断路器在研究过程中需要试验测试为设计提供参考，在其制造完成后则需要进行型式试验验证其可靠性。文中以15 kV电压等级的负压耦合型混合式直流断路器为例，对其短路电流开断过程进行仿真并提取了关键点电应力；阐述了两电平电压源合成试验方法，设计了适用于负压耦合型混合式直流断路器的两电平电压源合成试验回路，并优化了参数选取；将两电平回路下开断过程的仿真结果与开断过程所需的电应力进行对比，证明了两电平电压源合成试验方法可以提供开断过程所需的电压与电流应力，验证了两电平合成试验方法的等效性与可行性。文中研究结果可为高压直流断路器的研究、设计及试验提供参考。

Abstract

DC circuit breaker needs to be tested during the research process so to provide reference for the design and type test shall be performed for reliability verification after its manufacture. In this paper

the negative voltage coupling type hybrid DC circuit breaker at 15 kV is taken as an example to simulate its short circuit current interruption process and extract the key electrical stress. The two-level voltage source synthetic test method is described

the two-level voltage source synthetic test circuit which is suitable for the negative-voltage coupling hybrid DC circuit breaker is designed and the parameter selection is optimized. The simulation results of test circuit with the electrical stress required in the interruption process are compared. It is proved that the two-level voltage source synthetic test method can provide the voltage and current stress required for the interruption process. Both equivalence and feasibility of the two-level synthetic test method are verified. The results in this paper can provide reference for the research

design and experiment of HVDC circuit breaker.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on Interruption Characteristics of Low Voltage Hybrid DC Circuit Breaker

Research on Influence of Key Parameters in Hybrid DC Circuit Breakers on Arc Current Commutation Characteristics

Research on Interruption Characteristics of Low Voltage Hybrid DC Circuit Breaker

Review of the Equivalence Between Oscillating Wave Voltage and AC Methods for XLPE Cables Withstand and Partial Discharge Measurement

Empirical Study on the Sensing Characteristics of 1100 kV GIS UHF Online Monitoring Instruments

Related Author

YIN Jianning

XIAO Yu

LANG Xiaojian

CHEN Shidong

XIONG Dezhi

QIU Jun

FENG Zeming

DUAN Xiongying

Related Institution

Hunan Province Key Laboratory of Intelligent Electrical Measurement and Application Technology, Grid Hunan Electric Power Limited Company Power Supply Service Center (Metrology Center)

State Grid Hunan Electric Power Limited Company

School of Electrical Engineering, Xi'an University of Technology

School of Electrical Engineering, Dalian University of Technology

Hunan Province Key Laboratory of Intelligent Electrical Measurement and Application Technology (State Grid Hunan Electric Power Limited Company Power Supply Service Center (Metrology Center))

⁰