Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit

ZHAO Jing; SHAO Mengya; LIANG Jingxuan; LIN Jian; YOU Yimin; TAN Shaofeng

doi:10.13296/j.1001-1609.hva.2024.12.006

您当前的位置：

首页 >

文章列表页 >

Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit

Research & Analysis | 更新时间：2025-04-26

- Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit
- High Voltage Apparatus Vol. 60, Issue 12, Pages: 49-56(2024)
- 作者机构：
  
  1.厦门理工学院电气工程与自动化学院，福建　厦门　 361024
  2.厦门华电开关有限公司，福建　厦门　 361006
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2024.12.006
  CLC：
- Received：20 June 2024，
  
  Revised：25 August 2024，
  
  Published：16 December 2024
- 稿件说明：
移动端阅览
ZHAO Jing, SHAO Mengya, LIANG Jingxuan, et al. Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit[J]. High voltage apparatus, 2024, 60(12): 49-56.
DOI：

ZHAO Jing, SHAO Mengya, LIANG Jingxuan, et al. Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit[J]. High voltage apparatus, 2024, 60(12): 49-56. DOI： 10.13296/j.1001-1609.hva.2024.12.006.

摘要

针对某型号40.5 kV气体绝缘环网柜开关室中复合套管和连接铜排区域容易发生局部放电现象，导致柜体绝缘性能降低的问题，采用SolidWorks软件对复合套管与连接铜排区域建立三维模型，借助Ansys Workbench有限元分析软件对复合套管与连接铜排区域进行了电场仿真，结果表明：内六角圆柱头螺钉端部、引弧静触头顶端、连接铜排顶端、连接铜排折弯处的电场较为集中。在此基础上采取改变内六角螺钉的类型、在引弧静触头顶端增加均压屏蔽罩、加大连接铜排的圆角折弯半径和增加连接铜排与外壳前面板之间的距离等4种结构优化措施，有效地降低了套管和连接铜排区域的电场强度。最后，将优化后的复合套管和连接铜排进行样机组装并通过了绝缘试验验证。

Abstract

In view of partial discharge phenomenon of composite bushing and connecting copper bar area in the compartment of a certain type of 40.5 kV gas insulated ring main unit

which leads to the reduction of the insulation performance of the ring main unit

the SolidWorks software is used to set up a three-dimensional model of the composite bushing and connecting copper bar area

and then Ansys Workbench finite element analysis software is used to simulate the electric field of the composite bushing and connecting copper bar area. The results show that the electric field is concentrated on the end of the hexagon socket cylindrical head screw

top of the stationary contact of arc initiation

top of the connecting copper bar and the bending position of the connecting copper bar. On this basis

such four structural optimization measures as change of the type of hexagon socket screw

addition of a grading shield on the top of the stationary contact of arc initiation

increase of the bending radius of the rounded corner connecting copper bar the increase of the distance between the connecting copper bar and the front panel of the enclosure are adopted to effectively reduce the electric field intensity near the composite bushing and connecting copper bar area. Finally

the optimized composite bushing and connecting copper bar are assembled and the prototype has passed the insulation test verification.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear

Development of 1 100 kV GIS Composite Bushing at Altitude of 4 000 m

Dynamic Analysis on Key Parts of SF₆ High-voltage Circuit Breaker Based on Impact Load

Study and Analysis on Current-flow Capacity Improvement of Self-propelled Contact Finger of Circuit Breaker

Optimization Design on Spring Contact Finger Structure Based on Finite Element Method and Neural Network Method

Related Author

HUANG Jingjing

CHONG Jiali

SUI Xiangxu

LU Peng

LIU Xu

WANG Lijuan

FANG Qi

WANG Lei

Related Institution

College of Electrical Engineering and Automation,Fuzhou University

Henan Pinggao Electric Co, Ltd

Henan Pinggao Electric Co., Ltd.

School of Mechanical Engineering, Dalian Jiaotong University

Pinggao Group Co., Ltd.

⁰