USING SOFTWARE ANSYS TO ANALYZE ELECTROMAGNETIC PROCESS

WANG Shi  shan; WANG De  lin; LI Yan  ming

您当前的位置：

首页 >

文章列表页 >

USING SOFTWARE ANSYS TO ANALYZE ELECTROMAGNETIC PROCESS

更新时间：2025-04-26

- USING SOFTWARE ANSYS TO ANALYZE ELECTROMAGNETIC PROCESS
- High VoltageApparatus Issue 3, Pages: 27-30+33(2002)
- 作者机构：
  
  1. 西安交通大学电气学院
  2. 西安交通大学电气学院陕西西安710049
- 作者简介：
- 基金信息：
- DOI：
  CLC： TM154.1
- Published：2002
- 稿件说明：
移动端阅览
[1]王世山,王德林,李彦明.大型有限元软件ANSYS在电磁领域的使用[J].高压电器,2002(03):27-30+33.

WANG Shi shan, WANG De lin, LI Yan ming. USING SOFTWARE ANSYS TO ANALYZE ELECTROMAGNETIC PROCESS[J]. High voltageapparatus, 2002, (3): 27-30+33.
[1]王世山,王德林,李彦明.大型有限元软件ANSYS在电磁领域的使用[J].高压电器,2002(03):27-30+33. DOI：

WANG Shi shan, WANG De lin, LI Yan ming. USING SOFTWARE ANSYS TO ANALYZE ELECTROMAGNETIC PROCESS[J]. High voltageapparatus, 2002, (3): 27-30+33. DOI：

摘要

简单介绍了大型商用有限元软件ANSYS在电磁领域的使用

并以单线圈 2D变压器和双线圈 3D变压器的电磁过程为例加以说明

对线圈中每一线饼

甚至每一线匝在空载、常态和短路条件下的受力情况进行了全面分析。由于在短路条件下线匝之间挤压、悬空、反复振动

最终线圈可能受到整体损坏

因此

ANSYS的分析结果可为电力变压器的故障诊断提供理论依据

Abstract

This paper introduces the application of software ANSYS with finite element method（FEM）to analyze the electromagnetic process of 2D transformer with single winding and 3D transformer with double winding. The forces of each pie and turn are analyzed fully under conditions of no load

normal and short circuit. Under the condition of short circuit there exists pushing

pressing

suspending and vibrating between pies or turns of windings

so the whole winding may damaged finally. Therefore

the analysed results by ANSYS can give a theoretical reference to fault diagnosis of power transformer.

关键词

Keywords

references

Views

1905

下载量

206

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Assistant Design of Numerical Calculation and Electrical-stress-optimizing on Cable Accessories up to 10 kV

Calculation on Thermo-electricity Coupled Transient Temperature Field of High Voltage Current Limiting Fuse

Numerical Computation of Electrical Field Inside GIS Breaker Based on Calling APDL by VC++

Cam Optimization Design of Spring Operating Mechanism in High Voltage Switch Based on CAE Technology

Impact Response Analysis for Keeping-spring of Circuit Breaker Using ANSYS

Related Author

LI Zhe1

JIA Xian2

YIN Yi1

WANG Zi-jian1

HE Jun-jia1

YIN Xiao-gen1

CUI Jun-wei1

CAI Chuan1

Related Institution

Shanghai Feihang Electrical Equipment Ltd.

School of Electrical Engineering, Shanghai Jiaotong University

河北保定071003

华北电力大学电气工程学院

College of Electrical Engineering,North China Electric Power University

⁰