Study of Silicone Rubber Hydrophobicity Representation Method Using Dynamic Contact Angle

XU Zhi-niu; Lü Fang-cheng; LI Man; LI He-ming

doi:10.13296/j.1001-1609.hva.2010.10.002

您当前的位置：

首页 >

文章列表页 >

Study of Silicone Rubber Hydrophobicity Representation Method Using Dynamic Contact Angle

更新时间：2025-04-26

- Study of Silicone Rubber Hydrophobicity Representation Method Using Dynamic Contact Angle
- High VoltageApparatus Vol. 46, Issue 10, Pages: 6-9+15(2010)
- 作者机构：
  
  华北电力大学生物质发电成套设备国家工程实验室
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2010.10.002
  CLC： TM216.3
- Published：2010
- 稿件说明：
移动端阅览
[1]徐志钮,律方成,李嫚,和明.基于动态接触角的硅橡胶憎水性表征方法的研究[J].高压电器,2010,46(10):6-9+15.

XU Zhi-niu, Lü Fang-cheng, LI Man, et al. Study of Silicone Rubber Hydrophobicity Representation Method Using Dynamic Contact Angle[J]. High voltageapparatus, 2010, 46(10): 6-9+15.
[1]徐志钮,律方成,李嫚,和明.基于动态接触角的硅橡胶憎水性表征方法的研究[J].高压电器,2010,46(10):6-9+15. DOI： 10.13296/j.1001-1609.hva.2010.10.002.

XU Zhi-niu, Lü Fang-cheng, LI Man, et al. Study of Silicone Rubber Hydrophobicity Representation Method Using Dynamic Contact Angle[J]. High voltageapparatus, 2010, 46(10): 6-9+15. DOI： 10.13296/j.1001-1609.hva.2010.10.002.

摘要

当硅橡胶受到侵蚀和染污时

由于表面变得粗糙和溶质沉淀

导致接触角测量存在滞后效应

为了更合理表征硅橡胶的憎水性

将动态接触角方法用于硅橡胶憎水性的表征。该方法对材料表面通过注水/抽水的方式获得前进角/后退角。对洁净、浸泡、电晕和表面染污后的室温硫化硅橡胶涂层样本分别使用静态接触角方法、动态接触角方法进行测量。结果发现

浸泡、染污、电晕后的样本两种方法所得结果差别较大

静态接触角测量随机性较大且易受拍照时延的影响

对表面憎水性的表征能力不够

后退角能很好地表征材料的憎水性

后退角越小

则材料表面越容易被浸润。文中同时对浸泡、电晕、染污前后表面的粗糙度增加、溶质沉淀原因进行了分析

理论上解释了接触角测量的滞后效应。笔者的研究对硅橡胶及高分子材料的憎水性研究具有一定参考价值。

Abstract

Because of coarseness and solute deposition of surface

contact angle measurement of contaminated and eroded silicone rubber has hysteresis phenomenon.Dynamic contact angle method could be used to represent the hydrophobicity of silicone rubber better.The method obtained advancing contact angle and receding contact angle by injection and extraction deionized water on the surface respectively.The hydrophobicity of clean

immersed

corona and contaminated RTV（Room Temperature Vulcanization） silicone rubber coatings were measured by static contact angle method and dynamic contact angle method respectively.The result indicates that the difference between the advancing contact angle and the receding contact angle of the immersed

corona and contaminated samples is large.The measurement result of static contact angle of those samples has randomness

and easy to be influenced by delay time

so it can not reflect the surface hydrophobicity effectively

but the receding contact can reflect the surface hydrophobicity very well.The small receding angle indicates easy infiltration of the surface.In the meantime

the paper analyzed the reason of hysteresis of various samples′contact angle measurement.The study of the paper has some meaning for hydrophobicity study of silicone rubber and polymer materials.

关键词

Keywords

references

Views

385

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Thermal Aging Characteristics Analysis of HTV Silicone Rubber Composite Insulator Shed

Properties of Silicone Rubber of Insulator and Its Application in High Voltage Transmission Line

Study on Hydrophobicity and Withstand Characteristics of Natural Aging Silicone Rubber

Application of Fitting Based Contact Angle Algorithm in Silicone Rubber Hydrophobicity Detection

Discussion on Contaminating Method for High Temperature Vulcanizing Silicone Rubber Samples

Related Author

LYU Li

XIA Lingzhi

HUANG Hongfei

GUO Kaihang

CHENG Yang

REN Chengyan

SHAO Jun

ZHAO Yao-ming

Related Institution

State Grid Anhui Electric Power Research Institute

Beijing International S & T Cooperation Base for Plasma Science and Energy Conversion, Institute of Electrical Engineering Chinese Academy of Sciences

University of Chinese Academy of Sciences

Department of Polymer Materials and Engineering,South China University of Technology

State Key Laboratory of Electrical Insulation and Power Equipment of Xi’an Jiaotong University

⁰