Study of Influencing Factors on Polluted RTV Coatings Hydrophobicity Migration

XU Zhi-niu; L Fang-cheng; LI Man; LI He-ming; DONG Liang; WANG Ya-nan

doi:10.13296/j.1001-1609.hva.2011.04.007

您当前的位置：

首页 >

文章列表页 >

Study of Influencing Factors on Polluted RTV Coatings Hydrophobicity Migration

更新时间：2025-04-26

- Study of Influencing Factors on Polluted RTV Coatings Hydrophobicity Migration
- High VoltageApparatus Vol. 47, Issue 4, Pages: 7-12(2011)
- 作者机构：
  
  华北电力大学生物质发电成套设备国家工程实验室
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2011.04.007
  CLC： TM216
- Published：2011
- 稿件说明：
移动端阅览
[1]徐志钮,律方成,李嫚,李和明,董亮,王亚男.RTV涂层染污后憎水性迁移影响因素的研究[J].高压电器,2011,47(04):7-12.

XU Zhi-niu, L Fang-cheng, LI Man, et al. Study of Influencing Factors on Polluted RTV Coatings Hydrophobicity Migration[J]. High voltageapparatus, 2011, 47(4): 7-12.
[1]徐志钮,律方成,李嫚,李和明,董亮,王亚男.RTV涂层染污后憎水性迁移影响因素的研究[J].高压电器,2011,47(04):7-12. DOI： 10.13296/j.1001-1609.hva.2011.04.007.

XU Zhi-niu, L Fang-cheng, LI Man, et al. Study of Influencing Factors on Polluted RTV Coatings Hydrophobicity Migration[J]. High voltageapparatus, 2011, 47(4): 7-12. DOI： 10.13296/j.1001-1609.hva.2011.04.007.

摘要

研究室温硫化（room temperature vulcanization

RTV）硅橡胶涂层染污后憎水性迁移及其影响因素对RTV的应用具有指导意义。笔者以盐和灰的混合物模拟现场污秽

通过静态/动态接触角法表征憎水性

研究了迁移时间、温度、湿度、盐类型、灰类型、盐密、灰密对RTV涂层憎水性迁移速度的影响。结果表明:随着迁移时间的增加憎水性逐渐变好

迁移完全样本的接触角大于洁净样本;随温度增加迁移速度变快

且温度越高速度增加越快;随相对湿度增加迁移速度减慢

迁移所需时间非线性增大;ZnSO4迁移速度最快

NaNO3、NaCl、CaSO4相近;灰为硅藻土时污层的迁移速度快于高岭土的;随盐密/灰密（污秽度）的增加迁移速度有下降的趋势。

Abstract

It is important to study polluted room temperature vulcanization（RTV） silicone rubber coatings hydrophobicity migration and its influencing factors

which has guiding significance to RTV application.In the paper

mixture of salt and ash was used to simulate on-site pollution

and static contact angle/dynamic contact angle method is used to express hydrophobicity of RTV coatings.The influence of hydrophobicity migration duration time

temperature

humidity

salt type

ash type

salt deposition density（SDD）

non-souble salt deposition density（NSDD） on RTV coatings hydrophobicity migration speed was studied.The result indicates that: hydrophobicity become well with the increase of migration duration time and the contact angle of migrated well sample will be larger than that of the clean one.Hydrophobicity migration speed becomes fast with the increase of temperature and the higher temperature the faster increasing speed.Hydrophobicity migration speed becomes slower and migration needed time nonlinear increases with the increase of relative humidity

and the higher relative humidity the longer migration time.ZnSO4 has the fastest migration speed

and NaNO3

NaCl and CaSO4 have close migration speed.Kieselguhr has faster migration speed than kaolin.The migration speed will decrease with the increase of SDD/NSDD（pollotion degree）.

关键词

Keywords

references

Views

279

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Application of Fitting Based Contact Angle Algorithm in Silicone Rubber Hydrophobicity Detection

Thermal Aging Characteristics Analysis of HTV Silicone Rubber Composite Insulator Shed

Study on Hydrophobicity Diagnosis Method of Composite Insulator Based on Lightweight Convolution Neural Network

Study on Use of Additives to Improve Hydrophobicity and Tracking Resistance of Epoxy Material for Switchgear Cabinet

Effect of PRTV Coating on AC Flashover Voltage of Ice-covered Insulator Strings

Related Author

XU Zhi-niu1

L Fang-cheng1

ZHOU Jing-jing2

LI He-ming1

LYU Li

XIA Lingzhi

HUANG Hongfei

GUO Kaihang

Related Institution

金华电业局

National Engineering Laboratory for Biomass Power Generation Equipment,North China Electric Power University,Baoding 071003,China 2.Jinhua Electric Power Industry Bureau

State Grid Anhui Electric Power Research Institute

Beijing International S & T Cooperation Base for Plasma Science and Energy Conversion, Institute of Electrical Engineering Chinese Academy of Sciences

University of Chinese Academy of Sciences

⁰