Study on Discharge of Grading Rings for Insulators in the 500 kV Gangcheng Substation

WANG Li-ming1; HOU Zhi-gang1; MEI Hong-wei1; GUAN Zhi-cheng1

doi:10.13296/j.1001-1609.hva.2012.07.006

您当前的位置：

首页 >

文章列表页 >

Study on Discharge of Grading Rings for Insulators in the 500 kV Gangcheng Substation

更新时间：2025-04-26

- Study on Discharge of Grading Rings for Insulators in the 500 kV Gangcheng Substation
- High VoltageApparatus Vol. 48, Issue 7, Pages: 11-16(2012)
- 作者机构：
  
  1. 清华大学电机系
  2. 清华大学深圳研究生院
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2012.07.006
  CLC： TM216
- Published：2012
- 稿件说明：
移动端阅览
[1]王黎明,侯志刚,梅红伟,关志成.500kV港城变电站绝缘子均压环放电现象研究[J].高压电器,2012,48(07):11-16.

WANG Li-ming1, HOU Zhi-gang1, MEI Hong-wei1, et al. Study on Discharge of Grading Rings for Insulators in the 500 kV Gangcheng Substation[J]. High VoltageApparatus, 2012, 48(7): 11-16.
[1]王黎明,侯志刚,梅红伟,关志成.500kV港城变电站绝缘子均压环放电现象研究[J].高压电器,2012,48(07):11-16. DOI： 10.13296/j.1001-1609.hva.2012.07.006.

WANG Li-ming1, HOU Zhi-gang1, MEI Hong-wei1, et al. Study on Discharge of Grading Rings for Insulators in the 500 kV Gangcheng Substation[J]. High VoltageApparatus, 2012, 48(7): 11-16. DOI： 10.13296/j.1001-1609.hva.2012.07.006.

摘要

为了提高有限元数值仿真计算方法在研究外绝缘设备电场分布的准确性

对均压环与绝缘子串电场进行仿真分析

并通过设置仿真参数来获得均压环管径和安装位置最佳尺寸的依据。针对湛江500 kV港城变电站均压环对玻璃绝缘子串放电现象

运用ANSOFT软件建立了500 kV交流杆塔上均压环与绝缘子串全三维模型

研究了均压环管径和安装位置对绝缘子串电场分布影响的规律

并通过对电场强度的仿真分析解释了均压环对绝缘子频繁放电的原因。仿真分析中研究了均压环管径及其安装位置对最大电场强度的影响

进而得出了满足实际工程应用的最佳的均压环管径和安装位置

通过实际运行验证仿真结果对于消除绝缘子均压环放电效果明显。

Abstract

In order to improve the accuracy of finite element numerical simulation used in the study of the electric field distribution of external insulation equipment

the electric field of the grading ring and the insulator string was simulated and analyzed

and the optimized pipe diameter and install locations of the grading ring was obtained by setting different parameters.The three dimensional（3D） model of 500 kV substation with grading ring and insulators strings were established by using ANSOFT software.The effect of pipe diameter and install locations of grading ring on the electric field distribution of insulator strings was studied and the continuous discharge between grading ring and insulator was explained by the simulation analysis.The influence on the maximum electric field strength by the pipe diameter and install locations of the grading ring was studied in the simulation.On this basis

the optimized pipe diameter and install locations of the grading ring that satisfied practical engineering application was obtained.Finally

the feasibility of the simulation results used in eliminating discharge on the grading ring was demonstrated by the practical operation.

关键词

Keywords

references

Views

190

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Optimal Design of Grading Rings for 750 kV AC Composite Insulator

Simulation and Test of Potential Distribution for 750 kV Insulator String

Research on the Simulation of Glass or Porcelain Insulators in Series with 220 kV Composite Insulator

Research on Electric Field Distribution of Roof Insulator Under Humid Condition and Its Improving Strategy

Optimization for Grading Rings of High-speed Train Roof Insulator

Related Author

BO Xue-wei1

BIAN Xing-ming2

WANG Li-ming2

GAO De-gang1

REN Gui-qing1

HUO Feng

GU Li-li

CHEN Yong

Related Institution

Dalian Insulator Group Co.,Ltd.

State Grid Electric Power Research Institute

Henan Provincial Electric Power Science and Technology Research Institute

Huazhong University of Science and Technology

School of Electrical Engineering, Southwest Jiaotong University

⁰