Overload Capability Calculation for Oil-immersed Amorphous Alloy Transformers

WEN Zhengqi; LU Wenhua; DU Zhenbo; XIANG Dongdong; LI Jianchao

doi:10.13296/j.1001-1609.hva.2016.11.017

您当前的位置：

首页 >

文章列表页 >

Overload Capability Calculation for Oil-immersed Amorphous Alloy Transformers

更新时间：2025-04-26

- Overload Capability Calculation for Oil-immersed Amorphous Alloy Transformers
- High VoltageApparatus Vol. 52, Issue 11, Pages: 102-106(2016)
- 作者机构：
  
  1. 国网电力科学研究院武汉南瑞有限责任公司
  2. 河北钢铁集团邯钢公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2016.11.017
  CLC： TM421
- Published：2016
- 稿件说明：
移动端阅览
[1]文正其,卢文华,杜振波,向冬冬,李建超.油浸式非晶合金配电变压器过载能力核算方法研究[J].高压电器,2016,52(11):102-106.

WEN Zhengqi, LU Wenhua, DU Zhenbo, et al. Overload Capability Calculation for Oil-immersed Amorphous Alloy Transformers[J]. High voltageapparatus, 2016, 52(11): 102-106.
[1]文正其,卢文华,杜振波,向冬冬,李建超.油浸式非晶合金配电变压器过载能力核算方法研究[J].高压电器,2016,52(11):102-106. DOI： 10.13296/j.1001-1609.hva.2016.11.017.

WEN Zhengqi, LU Wenhua, DU Zhenbo, et al. Overload Capability Calculation for Oil-immersed Amorphous Alloy Transformers[J]. High voltageapparatus, 2016, 52(11): 102-106. DOI： 10.13296/j.1001-1609.hva.2016.11.017.

摘要

针对非晶合金配电变压器因过载导致烧损的情况

提出了一种油浸式非晶合金配电变压器过载能力校核方法。该方法以油浸式电力变压器负载导则为依据

确定了过载特定限制条件及过负荷校核流程

建立了从能量守恒角度研究了基于顶层油道油温的绕组热点温度预估模型。最后以一台SBH15系列非晶合金变压器为例

分别利用文中提出的热点温度预测模型和负载导则推荐的模型开展过载能力校核

结果表明

文中提供的方法对过载能力的考核更为严格。

Abstract

Aiming at amorphous alloy distribution transformer burnt fault due to overload

a new overload capability calculation method for oil-immersed amorphous alloy distribution transformer is proposed. Based on the oil-immersed power transformer load guide

the specific overload restrictions and the process of overload capability calculation are determined. And a new hot spot temperature prediction model is established on the basis of the top duct oil temperature following energy conservation. Finally

a SBH15 series amorphous alloy transformer is taken as an example to calculate the overload capability with the proposed hot spot temperature prediction model and the model suggested in the oil-immersed power transformer load guide

respectively. The results indicate that the proposed model can obtain more stringent overload capability criterion than the other.

关键词

Keywords

references

Views

126

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influence of Extreme Cold Climate on the Dynamic Distribution Characteristics of Moisture in Oil-immersed Transformer

Inversion Identification Method and Experimental Verification of Hot Spot Temperature in Three-core Cable Joints Based on Main Heat Flow Analysis

Calculation and Analysis of Hot Spot Temperature in 35 kV Oil-immersed Transformer Windings

Analysis of Load Loss and Winding Hot Spot Temperature of Oil Immersed Distribution Transformer Under Harmonic Current

Modification and Experimental Verification of Oil-immersed Transformer Thermal Circuit Model

Related Author

WANG Qiong

YANG Bo

MING Zifeng

ZHOU You

DOU Bingjie

DUAN Jingna

ZHANG Zhiqiang

HOU Aogang

Related Institution

Hunan Provincial Key Laboratory of Smart Grid Operation and Control, School of Electrical & Information Engineering, Changsha University of Science and Technology

Inner Mongolia Electric Power Science & Research Institute, Inner Mongolia Power Co., Ltd.

School of Electrical Engineering and Automation, Wuhan University

State Key Laboratory of Power Grid Environmental Protection, Wuhan University

Guangdong Zhongshan Power Supply Bureau of China Southern Power Grid

⁰