Finite Element Analysis of O-ring with Rectangular Groove Leakproof Structure in High Voltage Switchgear

TU Dehua; WEI Yajun; ZHANG Xin

doi:10.13296/j.1001-1609.hva.2019.04.009

您当前的位置：

首页 >

文章列表页 >

Finite Element Analysis of O-ring with Rectangular Groove Leakproof Structure in High Voltage Switchgear

更新时间：2025-04-26

- Finite Element Analysis of O-ring with Rectangular Groove Leakproof Structure in High Voltage Switchgear
- High VoltageApparatus Vol. 55, Issue 4, Pages: 60-64+71(2019)
- 作者机构：
  
  1. 厦门大学嘉庚学院机电工程学院
  2. 陶朗分选技术(厦门)有限公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2019.04.009
  CLC： TM564
- Published：2019
- 稿件说明：
移动端阅览
[1]涂德华,魏雅君,张鑫.高压开关设备用矩形槽O形密封圈密封结构的有限元分析[J].高压电器,2019,55(04):60-64+71.

TU Dehua, WEI Yajun, ZHANG Xin. Finite Element Analysis of O-ring with Rectangular Groove Leakproof Structure in High Voltage Switchgear[J]. High voltageapparatus, 2019, 55(4): 60-64+71.
[1]涂德华,魏雅君,张鑫.高压开关设备用矩形槽O形密封圈密封结构的有限元分析[J].高压电器,2019,55(04):60-64+71. DOI： 10.13296/j.1001-1609.hva.2019.04.009.

TU Dehua, WEI Yajun, ZHANG Xin. Finite Element Analysis of O-ring with Rectangular Groove Leakproof Structure in High Voltage Switchgear[J]. High voltageapparatus, 2019, 55(4): 60-64+71. DOI： 10.13296/j.1001-1609.hva.2019.04.009.

摘要

利用Ansys软件建立了高压开关设备用矩形槽O形密封圈模型

对该O形密封圈的变形和应力分布状况进行了数值模拟分析

研究了其工作时的受力、变形及密封效果。对该O形密封圈在不同压缩率、不同充气压力下的内应力及密封面接触应力分布进行了探讨

确定了仅考虑应力作用下O形密封圈材料容易失效的位置

并得出充气压力在1.6 MPa以下时O形密封圈没有被挤入上、下法兰间隙。

Abstract

In order to know deformation and sealing effect of O-ring with rectangular groove leakproof structure in high voltage switchgear

methods set up model for O-ring with rectangular groove leakproof structure in high voltage switchgear by ANSYS software

then the mechanical condition and deformation of the O-ring are analyzed numerically. Investigate stress and contact stress distribution of O-ring with rectangular groove in different compression rate and different gas pressure. The position where the material of O-ring is easy to fail under stress is determined

and it is concluded that the O-ring is not be squeezed into gap between top and bottom flange when the inflation pressure is below 1.6 MPa. The results can provide reference for design of O-ring with rectangular groove leakproof structure in high voltage switchgear.

关键词

Keywords

references

Views

133

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on Efficiency Optimization of Engineering Electromagnetic Repulsion Mechanism

Lightning Electromagnetic Transient Analysis of Offshore Wind Turbine Based on Finite Element Method

Study on Fatigue Characteristics of Offshore VSC-HVDC Converter Valve Tower in Operation

AUTOMATIC FINITE ELEMENT DIVISION METHOD FOR 3-D ELECTROMAGNETICFIELD BASED ON STL FILE FORMATE

APPLICATION OF MINIATURE CIRCUIT BREAKER TO THE SECONDARY CIRCUIT OF HIGH VOLTAGE SWITCHGEAR

Related Author

XU Yuanzhen

FANG Taixun

LYU Wei

LIU Shaofei

ZHANG Liang

ZHANG Jiankai

WANG Jianliang

ZHANG Ping

Related Institution

NR Electric Co., Ltd.

BR Electric Power Electronics Co., Ltd.

School of Artificial Intelligence and Data Science, Hebei University of Technology

Hebei Construction Investment Offshore Wind Power Co., Ltd.

Xi'an XD Power Systems Co., Ltd.

⁰