Typical Mechanical Fault Diagnosis of GW4-126 Disconnector Based on Torque and Angle Detection

LIU Chunlai; ZHOU Taotao; MA Hongming; ZHANG Hancheng; QIU Zhibin; HUANG Yuchen

doi:10.13296/j.1001-1609.hva.2020.02.035

您当前的位置：

首页 >

文章列表页 >

Typical Mechanical Fault Diagnosis of GW4-126 Disconnector Based on Torque and Angle Detection

更新时间：2025-04-26

- Typical Mechanical Fault Diagnosis of GW4-126 Disconnector Based on Torque and Angle Detection
- High VoltageApparatus Vol. 56, Issue 2, Pages: 232-239(2020)
- 作者机构：
  
  1. 云南电网有限责任公司电力科学研究院
  2. 武汉大学电气工程与自动化学院
  3. 南昌大学信息工程学院
  4. 国网武汉供电公司检修分公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2020.02.035
  CLC： TM564.1
- Published：2020
- 稿件说明：
移动端阅览
[1]刘春来,周涛涛,马宏明,张汉城,邱志斌,黄聿琛.基于力矩与转角检测的GW4-126型隔离开关典型机械故障诊断[J].高压电器,2020,56(02):232-239.

LIU Chunlai, ZHOU Taotao, MA Hongming, et al. Typical Mechanical Fault Diagnosis of GW4-126 Disconnector Based on Torque and Angle Detection[J]. High voltageapparatus, 2020, 56(2): 232-239.
[1]刘春来,周涛涛,马宏明,张汉城,邱志斌,黄聿琛.基于力矩与转角检测的GW4-126型隔离开关典型机械故障诊断[J].高压电器,2020,56(02):232-239. DOI： 10.13296/j.1001-1609.hva.2020.02.035.

LIU Chunlai, ZHOU Taotao, MA Hongming, et al. Typical Mechanical Fault Diagnosis of GW4-126 Disconnector Based on Torque and Angle Detection[J]. High voltageapparatus, 2020, 56(2): 232-239. DOI： 10.13296/j.1001-1609.hva.2020.02.035.

摘要

高压隔离开关是电力系统中一种重要的电力设备

而目前针对高压隔离开关机械故障的检测与诊断

尚无行之有效的检测诊断技术

为此文中开展隔离开关机械故障检测诊断技术研究。文中以某GW4-126型隔离开关为试验研究对象

在不破坏改变隔离开关原有轴系基础上提出一种隔离开关操作力矩与转角检测技术

测得隔离开关处于正常状态、轴承卡涩、三相不同期、合闸不到位等典型机械状态的操作力矩—转角曲线

对比分析得出隔离开关机械状态改变时其对应的操作力矩—转角曲线会发生相应的改变

由此提出基于操作力矩—转角曲线的纵向比较法与横向比较法来判断隔离开关机械状态

为隔离开关的机械故障检测与诊断提供参考

以及时发现隔离开关机械故障隐患

防止事故扩大造成更大的损失。

Abstract

An operating torque and rotation angle detecting technology for GW4-126 disconnector is put forward without needing to damage its original shaft system.The operating torque versus rotation angle curves are measured in typical mechanical states of the disconnector

such as normal state

jam of bearing

asynchronous action of three phases

and insufficient closing.It is concluded that the torque-angle curves will change with the mechanical state of the disconnector.On this basis

a longitudinal comparison method and a lateral comparison method based on the torque-angle curve are proposed to judge the mechanical state of the disconnector.Both methods can be applied to detection and diagnosis of the mechanical faults of the disconnector.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Fault Diagnosis of High Voltage Disconnector Based on Attitude Angle and Speed Curves

Review on Mechanical Fault Diagnosis of High-voltage Circuit Breakers Based on Vibration Diagnosis

Mechanical Fault Diagnosis Method of GIS Based on Improved MFCC

Mechanical Fault Diagnoses on Circuit Breaker Based on Radial Basis Function Classifier

Multi-signal Joint Identification and Intelligent Diagnosis of High Voltage Circuit Breaker Faults Based on VMD-BiLSTM

Related Author

ZHANG Jinbo

LI Kemeng

YE Zhe

SUN Zhengke

YUAN Huan

YANG Aijun

LI Liming

WANG Xiaohua

Related Institution

Xi'an High Voltage Apparatus Research Institute Co., Ltd.

School of Electrical Engineering, Xi'an Jiaotong University

Xi'an Power Supply Company of State Grid Shaanxi Electric Power Co., Ltd.

Pinggao Group Co., Ltd.

School of Electrical Engineering,Beijing Jiaotong University

⁰