Simulation Calculation and Test Verification of GIS Functional Module with Double-break Disconnector

LI Weiguo; ZHANG Changhong; YANG Xu; HUANG Zhongkang; JI Xiaoqing; LI Wanmin

doi:10.13296/j.1001-1609.hva.2020.03.005

您当前的位置：

首页 >

文章列表页 >

Simulation Calculation and Test Verification of GIS Functional Module with Double-break Disconnector

更新时间：2025-04-26

- Simulation Calculation and Test Verification of GIS Functional Module with Double-break Disconnector
- High VoltageApparatus Vol. 56, Issue 3, Pages: 30-38(2020)
- 作者机构：
  
  1. 南方电网超高压输电公司检修试验中心
  2. 上海思源高压开关有限公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2020.03.005
  CLC： TM595
- Published：2020
- 稿件说明：
移动端阅览
[1]黎卫国,张长虹,杨旭,黄忠康,季晓清,李万民.双隔离断口GIS功能模块仿真计算及试验验证[J].高压电器,2020,56(03):30-38.

LI Weiguo, ZHANG Changhong, YANG Xu, et al. Simulation Calculation and Test Verification of GIS Functional Module with Double-break Disconnector[J]. High voltageapparatus, 2020, 56(3): 30-38.
[1]黎卫国,张长虹,杨旭,黄忠康,季晓清,李万民.双隔离断口GIS功能模块仿真计算及试验验证[J].高压电器,2020,56(03):30-38. DOI： 10.13296/j.1001-1609.hva.2020.03.005.

LI Weiguo, ZHANG Changhong, YANG Xu, et al. Simulation Calculation and Test Verification of GIS Functional Module with Double-break Disconnector[J]. High voltageapparatus, 2020, 56(3): 30-38. DOI： 10.13296/j.1001-1609.hva.2020.03.005.

摘要

可实现GIS不停电扩建和耐压功能的双断口隔离开关（DDS）采用非标准结构的断口型式

为了验证这种特殊结构是否满足实际运行工况

文中通过Ansys有限元软件

建立双断口隔离开关机、电、热3D仿真模型

开展双断口隔离开关机械强度、绝缘强度、载流能力的仿真计算

并以双断口隔离开关真型样机开展绝缘试验、温升试验、动热稳定试验、机械寿命试验、高低温试验、母线转移电流试验、壳体水压试验。研究结果表明:壳体最大主应力为235.08 MPa

盖板最大等效应力为114.86 MPa

均小于许用应力;双断口隔离开关各部件场强均低于允许场强

并有一定裕度;滑动连接部分最大温升为56.5 K

壳体温升为17.3 K

内部导体和壳体温升均满足要求;试验结果验证了仿真计算的正确性。双断口隔离开关已应用于±800 kV东方换流站220 kV GIS的6个备用扩建间隔

设备运行良好。

Abstract

The double-fracture disconnect switch（DDS）is a solution to continue operating without shutting down during GIS extension and withstand tests

which is designed as an nonstandard structure.In order to verify that the DDS satisfies the actual operating conditions.In this paper

the 3 D simulation models of DDS for the mechanical

electrical

thermal field are established by Ansys.The simulation calculation of mechanical strength

insulation strength and current-carrying capability of the DDS are carried out.In addition

the insulation test

temperature-rise test

dynamical thermal stability test

mechanical life test

high and low temperature test

busbar transfer current test

shell water pressure test are carried on the real DDS as well.The results show that the maximum stress of the shell is235.08 MPa

and the maximum stress of cover plate is 114.86 MPa

which are both less than the allowable stress.It also show that the electrical field of each component in the DDS is lower than the allowable field strength.As for the temperature test

the maximum temperature rise of sliding joint and the shell are 56.5 K and 17.3 K.Temperature rise of both internal conductor and shell meet the requirements.In sum

the experimental results consistent with the simulation calculation.The DDS has been applied to 6 standby expansion intervals of 220 kV GIS in the±800 kV Dong-Fang converter station.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Fault Analysis of the Key Components of GIL in Converter Stations

Development of Three-phase Enclosed Insulating Spacer for 126 kV Clean Air GIS

Temperature Rise Calculation and Test of Large Capacity Dry-type Air-core Reactor Under AC and DC Superimposed Current

Research on Influence of Opening Lock System of Spring Mechanism on Opening Time of High Voltage Circuit Breaker

Fault Analysis of a Support Insulator for 500 kV GIL Tubular Busbar

Related Author

LI Weiguo

ZHANG Changhong

YANG Xu

ZHAO Guodong

CHU Jinwei

NAN Zhenle

WANG Yao

WU Shengwei

Related Institution

South China University of Technology

Xi’an XD Switchgear Electric Co.,Ltd.

Liaoning HV Electrical Products Quality Testing Co., Ltd.

Northeast Yucai Bilingual School

New Northeast Electric Group High Voltage Switchgear Co., Ltd.

⁰