Study on the Model Simpliflcation Method for the Calculation of Arc Pressure Rise in MV Switchgear

WU Tian; YANG Dong; LI Peng; LI Zijin; WU Yongcong; FANG Wen

doi:10.13296/j.1001-1609.hva.2020.03.006

您当前的位置：

首页 >

文章列表页 >

Study on the Model Simpliflcation Method for the Calculation of Arc Pressure Rise in MV Switchgear

更新时间：2025-04-26

- Study on the Model Simpliflcation Method for the Calculation of Arc Pressure Rise in MV Switchgear
- High VoltageApparatus Vol. 56, Issue 3, Pages: 39-45+53(2020)
- 作者机构：
  
  1. 三峡大学湖北省输电线路工程技术研究中心
  2. 武汉大学电气与自动化学院
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2020.03.006
  CLC： TM591
- Published：2020
- 稿件说明：
移动端阅览
[1]吴田,杨东,黎鹏,黎子晋,吴泳聪,方雯.中压开关柜内部电弧压力升计算——模型简化方法研究[J].高压电器,2020,56(03):39-45+53.

WU Tian, YANG Dong, LI Peng, et al. Study on the Model Simpliflcation Method for the Calculation of Arc Pressure Rise in MV Switchgear[J]. High voltageapparatus, 2020, 56(3): 39-45+53.
[1]吴田,杨东,黎鹏,黎子晋,吴泳聪,方雯.中压开关柜内部电弧压力升计算——模型简化方法研究[J].高压电器,2020,56(03):39-45+53. DOI： 10.13296/j.1001-1609.hva.2020.03.006.

WU Tian, YANG Dong, LI Peng, et al. Study on the Model Simpliflcation Method for the Calculation of Arc Pressure Rise in MV Switchgear[J]. High voltageapparatus, 2020, 56(3): 39-45+53. DOI： 10.13296/j.1001-1609.hva.2020.03.006.

摘要

中压开关柜内部电弧故障时有发生

其短时间释放出的巨大能量引起隔室内部压力迅速上升

对设备、建筑物以及工作人员的安全造成了严重威胁。基于零部件规则化和隔室等容积替代的简化原则

提出了开关柜复杂模型简化方法;利用CFD法计算了不同简化模型的压力分布规律

给出了模型最优简化方法;对SCM法与CFD法获得的计算结果进行了对比

分析了两者的差异。结果表明:采用规则化—等容积替代混合方式简化模型获得的结果与原始模型吻合较好

计算时间缩短了约54.39%;当泄压板打开后

隔室内部的压强分布差异较大

采用SCM法获得的结果误差较大

应采用CFD法进行求解。

Abstract

The arcing fault inside medium-voltage（MV） switchgear happened occasionally.The great energy is released in a short time in the switchgear

resulting in pressure rise rapidly

which caused a serious threat to the safety of the equipment

buildings and personnel.Based on the simplified principles such as regularization replacement of the parts and isovolumetric replacement of the compartment

the simplified methods for the switchgear complex model are proposed in the paper.The pressure distribution for the different simplified models are calculated by the CFD

and the best simplified method for the model is given.The results are calculated by the pressure rise standard calculation method（SCM） and CFD

and the difference of both is analyzed.The results show that the model obtained by combined with the regularization replacement of the parts and the isovolumetric replacement of the compartment can get similar results with the original model

and the computation time is reduced by 54.39%.After the pressure relief cover is open

the pressure distribution has a great difference in the compartment.The result error is big by using SMC

and the CFD should be adopted for the switchgear.

关键词

Keywords

references

Views

147

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Pressure Rise Calculation and Pressure Relief Efficiency Analysis in the Cable Room of Switchgear Due to Internal Short-circuit Explosion

Simulation and Experimental Study on Partial Discharge Decomposition Components of Air-insulated Switchgear Cabinet Considering the Influence of Temperature and Humidity

Research on the Influence of Temperature and Humidity on the Physical Signal of Partial Discharge of Switchgear

RESEARCH ON THE CHARACTERISTICS OF ULTRASONIC SIGNALS OF PARTIAL DISCHARGE IN 12V SWITCHGEAR CABINET

A Microcontroller-based Protection Unit for Switchgear of Terminal Users

Related Author

黎子晋

方蓓贝

黎鹏

肖盼

吴田

普子恒

JI Hongquan

XIN Feng

Related Institution

China Three Gorges University

湖北省输电线路工程技术研究中心(三峡大学)

State Grid Beijing Electric Power Company Urban Power Supply Company

State Grid Beijingg Electric Power Company

Power Research Institute of State Grid Beijing Electric Power Co., Ltd.

⁰