Method to Diagnose the Concentricity of Tulip Contacts of a Medium Voltage Circuit Breaker Handcart Based on the Armature Current of a BLDCM

WANG Gang; PENG Yanqing; ZHUANG Zhijian; SUN Lijie; XIONG Yiwei

doi:10.13296/j.1001-1609.hva.2020.03.007

您当前的位置：

首页 >

文章列表页 >

Method to Diagnose the Concentricity of Tulip Contacts of a Medium Voltage Circuit Breaker Handcart Based on the Armature Current of a BLDCM

更新时间：2025-04-26

- Method to Diagnose the Concentricity of Tulip Contacts of a Medium Voltage Circuit Breaker Handcart Based on the Armature Current of a BLDCM
- High VoltageApparatus Vol. 56, Issue 3, Pages: 46-53(2020)
- 作者机构：
  
  1. 厦门理工学院电气工程与自动化学院
  2. ABB(中国)有限公司中压产品技术中心
  3. 国网娄底供电公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2020.03.007
  CLC： TM33;TM561
- Published：2020
- 稿件说明：
移动端阅览
[1]王刚,彭彦卿,庄志坚,孙利杰,熊逸伟.基于无刷直流电机电流的断路器手车梅花触头对中度诊断方法[J].高压电器,2020,56(03):46-53.

WANG Gang, PENG Yanqing, ZHUANG Zhijian, et al. Method to Diagnose the Concentricity of Tulip Contacts of a Medium Voltage Circuit Breaker Handcart Based on the Armature Current of a BLDCM[J]. High voltageapparatus, 2020, 56(3): 46-53.
[1]王刚,彭彦卿,庄志坚,孙利杰,熊逸伟.基于无刷直流电机电流的断路器手车梅花触头对中度诊断方法[J].高压电器,2020,56(03):46-53. DOI： 10.13296/j.1001-1609.hva.2020.03.007.

WANG Gang, PENG Yanqing, ZHUANG Zhijian, et al. Method to Diagnose the Concentricity of Tulip Contacts of a Medium Voltage Circuit Breaker Handcart Based on the Armature Current of a BLDCM[J]. High voltageapparatus, 2020, 56(3): 46-53. DOI： 10.13296/j.1001-1609.hva.2020.03.007.

摘要

目前

市场上可抽出式高压开关柜无法确认断路器手车梅花触头与静触头的对中度是否良好。文中提出了以无刷直流电机作为底盘车驱动电机

利用电枢电流数据实现手车梅花触头和静触头对中度诊断的方法。首先

为确定电枢电流的影响因素

分析无刷直流电机数学模型并仿真验证;利用具有不同偏心距离的静触头代替试验台原静触头

模拟不同程度的对中偏差;其次

以均值滤波和高斯拟合处理啮入阶段曲线

提取拟合函数参数A、xmax和啮入阶段电流均值为曲线特征

训练BP神经网络模型用于对中度诊断;最后

采集新数据

对所述方法进行试验验证。结果表明

所述方法对手车梅花触头和静触头对中度识别精度高。该方法为断路器手车梅花触头对中度诊断提供了一种思路。

Abstract

At present

there is no method for high voltage withdrawable switchgears to determine whether the concentricity of the tulip contacts of a circuit breaker handcart is good.This paper used a brushless DC motor as the driving motor for the circuit breaker handcart

and a method to diagnosis the concentricity of the tulip contacts of a medium voltage circuit breaker handcart was proposed.First of all

the mathematic model of the brushless DC motor was analyzed to determine the influencing factor of armature current.Static contacts with different eccentric distances were used to replace the original static contacts of the test bed to simulate different degrees of center deviation.Secondly

the current curves were processed by mean filter and Gauss fitting

and the parameter of the fitting function including A

xmax and the mean current of the meshing stage were extracted as the curves characteristics.The characteristics was used to train a BP neural network which was used to diagnosis the concentricity of tulip contacts.Finally

more data was sampled to test the method.It has been proved that the method was able to recognize different degrees of center deviation

and the method is high accuracy.It can provide a new idea to diagnosis the concentricity of tulip contacts of a medium voltage circuit breaker handcart.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation Design and Optimization of Permanent-magnet-motor Operating Mechanism for Vacuum Circuit Breaker with Long Clearance

Fault Diagnosis Algorithm on Spring Operating Mechanism for High Voltage Circuit Breaker and Load Switch Based on Motor Current

Design Simulation and Optimization of Fast Electromagnetic Repulsion Mechanism for Mechanical DC Circuit Breaker

Research on Key Technologies of PMA Based Synchronous Switching

Pattern Recognition of Partial Discharge in Oil-paper Insulation Based on Time Series

Related Author

DING Can

WANG Zhoulin

DING Yiling

LI Jinqi

JI Yiwei

ZHAO Lihua

WU Yuezheng

WANG Jiacan

Related Institution

State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University

College of Electrical Engineering & New Energy, China Three Gorges University

School of Automation, Northwest University of Technology

School of Electrical Engineering, Sichuan University

Lijiang Power Supply Bureau of Yunnan Power Grid Co., Ltd.

⁰