Study on AC Withstand Voltage Breakdown Discharge Location of GIL Equipment Based on Audible-signal

LIU Tong; TENG Yun; YANG Jinggang; MA Yong; ZHAO Ke; XIA Feng; YUAN Guogang

doi:10.13296/j.1001-1609.hva.2021.01.004

您当前的位置：

首页 >

文章列表页 >

Study on AC Withstand Voltage Breakdown Discharge Location of GIL Equipment Based on Audible-signal

更新时间：2025-04-26

- Study on AC Withstand Voltage Breakdown Discharge Location of GIL Equipment Based on Audible-signal
- High VoltageApparatus Vol. 57, Issue 1, Pages: 26-32+40(2021)
- 作者机构：
  
  1. 国网江苏省电力有限公司电力科学研究院
  2. 国网江苏省电力有限公司检修分公司
  3. 3. 上海睿深电子科技有限公司
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2021.01.004
  CLC： TM75
- Published：2021
- 稿件说明：
移动端阅览
[1]刘通,腾云,杨景刚,马勇,赵科,夏峰,袁国刚.基于可听声的GIL设备交流耐压击穿放电定位研究[J].高压电器,2021,57(01):26-32+40.

LIU Tong, TENG Yun, YANG Jinggang, et al. Study on AC Withstand Voltage Breakdown Discharge Location of GIL Equipment Based on Audible-signal[J]. High voltageapparatus, 2021, 57(1): 26-32+40.
[1]刘通,腾云,杨景刚,马勇,赵科,夏峰,袁国刚.基于可听声的GIL设备交流耐压击穿放电定位研究[J].高压电器,2021,57(01):26-32+40. DOI： 10.13296/j.1001-1609.hva.2021.01.004.

LIU Tong, TENG Yun, YANG Jinggang, et al. Study on AC Withstand Voltage Breakdown Discharge Location of GIL Equipment Based on Audible-signal[J]. High voltageapparatus, 2021, 57(1): 26-32+40. DOI： 10.13296/j.1001-1609.hva.2021.01.004.

摘要

为对GIL设备耐压试验时击穿放电点进行准确定位

文中选取110 kV GIS上的一段母线气室

模拟GIL设备开展基于可听声的GIL设备交流耐压击穿放电定位研究

针对GIL设备击穿性放电时可听声信号中的背景噪声

首先综合基于完备总体平均经验模态分解（complete ensemble empirical mode decomposition with adaptive noise

CEEMDAN）和小波阈值算法研究了声信号的去噪方法

并将声音信号中的背景噪声进行去除

然后采用时差法以直达声上升沿为标定时刻进行时延估计

实现放电点的空间定位。测试分析结果表明:所提出的去噪方法能有效抑制GIL击穿性放电时声信号中的噪声干扰

基于可听声的定位方法成功地确定了放电点

定位误差控制在15 cm之内

较好地满足了工程需求。

Abstract

For accurately locating breakdown discharge point of GIL equipment in withstand voltage test

in this paper

a section of busbar compartment on 110 kV GIS is selected to simulate GIL equipment and perform the study on AC withstand voltage breakdown discharge location of GIL equipment based on audible signal.In view of the background noise in the audible signal in case of breakdown discharge of GIL equipment

the denoising method of the acoustic signal is firstly studied with the combination of complete ensemble empirical mode decomposition with adaptive noise（CEEMDAN） and the wavelet threshold algorithm

the background noise in the acoustic signal is removed

then the time difference method is used and the direct acoustic start edge is taken as the calibration time to estimate the time delay to achieve the space location of discharge point.It is shown by the test and analysis result that the proposed de-noising method can suppress effectively the noise interference of acoustic signal in the breakdown discharge of GIL

and the location method based on audible signal determines the discharge point successfully with location error within 15 cm and can meet the engineering requirements.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on GIL Mechanical Fault Detection System Based on Combined Vibration and Acoustic Location Technology

Research Review on Tri-post Insulator for EHV/UHV GIL

White Noise Suppression Method of Partial Discharge Ultrasonic Signal of Transformer Based on Improved Wavelet Threshold-CEEMDAN

Fault Analysis of a Support Insulator for 500 kV GIL Tubular Busbar

Research Progress on Metal Particle Issues Inside GIL

Related Author

XU Aihua

ZANG Chunyan

LI Yishuo

HU Hongbo

XU Hao

XU Shengbo

GUO Hai

CHEN Jing

Related Institution

School of Electrical and Electronic Engineering, Huazhong University of Science and Technology

Hubei Institute of Measurement and Testing Technology

Qujing Bureau of EHV Cornpany of China Southern Power Grid Corporation

College of Electrical and Electronics Engineering, Huazhong University of Science and Technology

Wuhan Intelligent Equipment Industrial Institute Co., Ltd.

⁰