Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear

HUANG Jingjing; CHONG Jiali

doi:10.13296/j.1001-1609.hva.2021.01.010

您当前的位置：

首页 >

文章列表页 >

Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear

更新时间：2025-04-26

- Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear
- High VoltageApparatus Vol. 57, Issue 1, Pages: 68-74(2021)
- 作者机构：
  
  福州大学电气工程与自动化学院
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2021.01.010
  CLC： TM216.52;TM591
- Published：2021
- 稿件说明：
移动端阅览
[1]黄晶晶,种佳丽.KYN61-40.5 kV开关柜穿墙套管的电场仿真及结构优化[J].高压电器,2021,57(01):68-74.

HUANG Jingjing, CHONG Jiali. Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear[J]. High voltageapparatus, 2021, 57(1): 68-74.
[1]黄晶晶,种佳丽.KYN61-40.5 kV开关柜穿墙套管的电场仿真及结构优化[J].高压电器,2021,57(01):68-74. DOI： 10.13296/j.1001-1609.hva.2021.01.010.

HUANG Jingjing, CHONG Jiali. Electric Field Simulation and Structure Optimization for Wall Bushing of KYN61-40.5 kV Switchgear[J]. High voltageapparatus, 2021, 57(1): 68-74. DOI： 10.13296/j.1001-1609.hva.2021.01.010.

摘要

文中针对KYN61-40.5 kV开关柜母线室中穿墙套管容易发生局部绝缘老化导致环氧材料寿命降低的问题

运用Solidworks软件对穿墙套管区域建立三维模型。通过Ansys Workbench软件对穿墙套管区域进行了电场仿真。在工频耐压峰值下

分别仿真了单个地电位屏蔽环、悬浮电位屏蔽环和高、地电位双屏蔽环3种结构方案。对比3种结构方案下穿墙套管的环氧材料内部以及内外部空气域的电场分布

分析了高、地电位屏蔽环安装位置对电场分布的影响

结果表明:双屏蔽环的屏蔽方案更为优化

在D

取值35～45 mm、D

≈（60-D

）时为较佳的优化方案。该方案能够有效的改善穿墙套管区域电场分布不均匀的问题

提高穿墙套管的绝缘水平。

Abstract

In this paper

the problem of the life of epoxy materials is reduced due to the partial insulation aging of the wall bushings in the busbar room of KYN61-40.5 kV switchgear.Solidworks software is used to build a three-dimensional model of the wall bushing area

which is worn by Ansys Workbench software.The electric field simulation is performed in the wall casing area.Under the peak of power frequency withstand voltage

three kinds of structural schemes of single ground potential shielding ring

floating potential shielding ring and high and ground potential double shielding ring are simulated respectively.Comparing the electri

c field distribution of the inside and outside air domains of the epoxy material through the wall bushing under the three structural schemes

the influence of the installation position of the high and ground potential shielding rings on the electric field distribution is analyzed.The results show that the shielding scheme of the double shielding ring is more optimization

when D

is 35～45 mm and D

≈（60-D

）

it is a better optimization scheme.This scheme can effectively improve the problem of uneven electric field distribution in the wall bushing area and improve the insulation level of the wall bushing.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit

Electric Field Analysis and Shielding Optimization of 40.5 kV Wall Bushing

Electric Field Optimization and Structure Design of Wall Bushing in 40.5kV Air-insulated Switchgear

Research on Key Technologies of Installation and Use of 40.5 kV Switchgear Wall Bushing

Dynamic Analysis on Key Parts of SF₆ High-voltage Circuit Breaker Based on Impact Load

Related Author

SHAO Mengya

LIANG Jingxuan

LIN Jian

YOU Yimin

TAN Shaofeng

ZHAO Jing

HAN Shaigen

CAO Bin

Related Institution

School of Electrical Engineering & Automation, Xiamen University of Technology

Xiamen Huadian Switchgear Co., Ltd.

JSHP,Transformer

WisestPower

Chinese Electric Power Research Institute

⁰