Study and Analysis on Tolerance Chain of Operating Mechanism for Circuit Breaker Based on Reliability

TU Zhaoyang; KE Zhanhuang; YANG Canli; ZHONG Shuling

doi:10.13296/j.1001-1609.hva.2021.06.031

您当前的位置：

首页 >

文章列表页 >

Study and Analysis on Tolerance Chain of Operating Mechanism for Circuit Breaker Based on Reliability

更新时间：2025-04-26

- Study and Analysis on Tolerance Chain of Operating Mechanism for Circuit Breaker Based on Reliability
- High VoltageApparatus Vol. 57, Issue 6, Pages: 233-239(2021)
- 作者机构：
  
  1. 国家能源集团福建能源有限责任公司
  2. 国电泉州热电有限公司
  3. 厦门理工学院
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2021.06.031
  CLC： TM561
- Published：2021
- 稿件说明：
移动端阅览
TU Zhaoyang, KE Zhanhuang, YANG Canli, et al. Study and Analysis on Tolerance Chain of Operating Mechanism for Circuit Breaker Based on Reliability[J]. High voltageapparatus, 2021, 57(6): 233-239.
DOI：

TU Zhaoyang, KE Zhanhuang, YANG Canli, et al. Study and Analysis on Tolerance Chain of Operating Mechanism for Circuit Breaker Based on Reliability[J]. High voltageapparatus, 2021, 57(6): 233-239. DOI： 10.13296/j.1001-1609.hva.2021.06.031.

摘要

针对断路器操动机构零件公差积累后造成脱扣力过大和扣接量过大或过小

影响断路器动作可靠性问题。通过对机构的脱扣部分传动链进行受力分析找出影响合闸可靠性的几个较关键的零部件

分析扣接量对合闸脱扣的影响和画出合闸脱扣系统扣接量的尺寸链。并对储能保持状态时的机构扣接量进行公差链计算

发现现有产品的公差配合不满足完全互换情况下的扣接量的取值范围

通过公差链的仿真分析

找出影响合闸脱扣力及扣接量大小的关键零部件和尺寸

得到影响脱扣力和扣接量的敏感度和贡献度的关键零部件及其尺寸。对现有的设计公差进行优化设计

实现了产品的公差链满足完全互换条件下的技术参数。最终解决了零件公差影响断路器可靠合闸的问题。

Abstract

In view of the problem that operation reliability of the circuit breaker is affected due to excessive tripping force and excessive or small amount of buckling after the accumulation of tolerances of the parts of operating mechanism for the circuit breaker several key parts affecting closing reliability are found out through the force analysis of the transmission chain of the tripping part of the mechanism.The influence of the amount of buckling on the closing and tripping is analyzed and the dimensional chain of the buckling of the closing and tripping system is drawn.The tolerance chain calculation of the buckling amount of the mechanism in the charge holding condition is performed

finding that the tolerance fit of the existing product does not meet the value range of the buckling amount under the condition of complete interchange.Through the simulation analysis of the tolerance chain

the key parts and dimensions affecting the closing and tripping force and the amount of buckling are found out and the key parts and their dimensions affecting the sensitivity and contribution of the tripping force and the amount of buckling are obtained.The optimization design of the existing design tolerances is performed and the tolerance chain of the product fully meeting the technical parameters under the condition of complete interchange is achieved.Finally

the problem of parts tolerance affecting the reliable closing operation of the circuit breaker is solved.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on Influence of Piezoelectric Material Properties and Element Size on Sensitivity of Piezoelectric Sensor for Partial Discharge Monitoring of Transformer

Study and Design of Rogowski Coil for Partial Discharge Signal Measurement

Ultrasonic Detection of Partial Discharge on Typical Defects in GIS

Calibration of UHF Sensor for Detection of Partial Discharge in Transformer

Investigation of Improvement of Sensitivity Verification of Partial Discharge Detection Using UHF Method in GIS

Related Author

ZHU Jiayi

GAO Jinghui

LIU Yongbin

CHEN Chuan

WANG Yan

CHEN Guifeng

LUO Zheng

FANG Chunhua

Related Institution

State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University

Department of Electric Power Sensing Technology, Global Energy Interconnection Research Institute Co., Ltd.

Zhejiang Seluke Electric Co., Ltd.

College of Electricity and New Energy, China Three Gorges University

Hubei Provincial Engineering Technology Research Center for Power Transmission Line, China Three Gorges University

⁰