Electric Field Analysis and Optimization Design of Insulation Structure of 12 kV Vacuum Interrupter

DAI Dongyun; LIU Shuquan; YOU Yimin; PENG Zhenbo; XI Huanyu

doi:10.13296/j.1001-1609.hva.2024.06.007

您当前的位置：

首页 >

文章列表页 >

Electric Field Analysis and Optimization Design of Insulation Structure of 12 kV Vacuum Interrupter

Research & Analysis | 更新时间：2025-04-26

- Electric Field Analysis and Optimization Design of Insulation Structure of 12 kV Vacuum Interrupter
- High Voltage Apparatus Vol. 60, Issue 6, Pages: 50-56(2024)
- 作者机构：
  
  厦门理工学院电气工程与自动化学院，福建　厦门　 361024
- 作者简介：
- 基金信息：
- DOI：10.13296/j.1001-1609.hva.2024.06.007
  CLC：
- Received：07 January 2024，
  
  Revised：20 March 2024，
  
  Published：16 June 2024
- 稿件说明：
移动端阅览
DAI Dongyun, LIU Shuquan, YOU Yimin, et al. Electric Field Analysis and Optimization Design of Insulation Structure of 12 kV Vacuum Interrupter[J]. High voltage apparatus, 2024, 60(6): 50-56.
DOI：

DAI Dongyun, LIU Shuquan, YOU Yimin, et al. Electric Field Analysis and Optimization Design of Insulation Structure of 12 kV Vacuum Interrupter[J]. High voltage apparatus, 2024, 60(6): 50-56. DOI： 10.13296/j.1001-1609.hva.2024.06.007.

摘要

由于12 kV真空灭弧室工频电压老炼试验时，瓷壳内部出现局部击穿现象，需要对其内部结构进行研究，寻找一种改善灭弧室内部电位分布的绝缘优化方案。文中根据真空灭弧室的实际尺寸建立了三维电场计算模型，采用有限元计算得到了各部分的电场分布。对真空灭弧室的动静触头和屏蔽罩的绝缘强度进行了分析，根据其计算结果，对触头片边缘圆角、半径及其开槽宽度进行了优化，并对屏蔽罩的构造进行了改进，基于该优化方案进行电场分析，最后优化后的样机通过了工频电压老炼试验验证。

Abstract

Due to the local breakdown phenomenon inside the porcelain shell during the power frequency voltage burn-in test of 12 kV vacuum interrupter

it is necessary to study its internal structure to find an insulation optimization solution to improve the internal potential distribution of the interrupter. In this paper

a three-dimensional electric field calculation model is set up based on the actual size of the vacuum interrupter

and the electric field distribution of each part is obtained by finite element calculation. The insulation strength of the moving and stationary contacts as well as the shield of the vacuum interrupter is analyzed. According to the calculation results

the edge fillet

radius and slot width of the contact piece are optimized and the structure of the shield is improved. The electric filed analysis is performed on the basis of the optimization scheme. Finally

the optimized prototype passed the power frequency voltage burn-in test verification.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Electric Field Simulation and Insulation Test for the Improved Bushing on the Converter Transformer

Typical Fault Analysis Caused by Shielded Separable Connector

Simulation Study on the Influence of Electric Field of 500 kV Single Circuit Transmission Line on UAV

Research and Design of High Voltage Non-contact AC Electroscope

Electric Field Simulation and Optimization of Composite Bushing and Connecting Copper Bar Area of 40.5 kV Gas-insulated Ring Main Unit

Related Author

LI Weiguo

ZHANG Changhong

XIA Gulin

LU Wenhao

HE Ping

SUN Youliang

WANG Dongfang

MA Yongqiang

Related Institution

Baoding Tianwei Baobian Electric Co., Ltd.

Nanjing Electric Group Co., Ltd.

Maintenance & Test Center of EHV Power Transmission Company China Southern Power Grid

State Grid Ningxia Electric Power Corporation Research Institute

Wuzhong Company of State Grid Ningxia Power Co

⁰